|
Post by muvit madness on Aug 5, 2008 23:05:18 GMT 11
Oi Yarno Hows it going another month has gone by Time to make with some pics eh!!. Dont forget us ;D cheeers muvit
|
|
|
Post by mattybmusv3800 on Aug 8, 2008 21:51:49 GMT 11
Hi Ray, Matt here. Just wondering if you have uploaded those pics of my car that you took the other day. im gonna get some more and upload em here aswell. matt
|
|
|
Post by Yarno on Aug 10, 2008 16:39:01 GMT 11
Don't worry I haven't forgotten about ya's, just haven't done much as I have been away and had a couple of big weekends. Here's most of it, I have been working on the rear 4 mounts and they are made and half welded in as I'll have to take the body off to fully weld.
|
|
|
Post by Yarno on Aug 10, 2008 16:40:13 GMT 11
|
|
|
Post by Yarno on Aug 10, 2008 16:40:55 GMT 11
|
|
|
Post by Yarno on Aug 10, 2008 16:41:31 GMT 11
|
|
|
Post by Yarno on Aug 10, 2008 16:42:18 GMT 11
|
|
|
Post by Yarno on Aug 10, 2008 16:42:52 GMT 11
|
|
|
Post by Yarno on Aug 17, 2008 15:20:21 GMT 11
Ok some more photos... mounts still though I'm afraid Mount behind front tyres not finished yet but need to remove the body to finish.. Front mounts..
|
|
|
Post by Yarno on Aug 17, 2008 15:24:05 GMT 11
|
|
|
Post by Yarno on Aug 25, 2008 18:20:49 GMT 11
Should be getting a set of diffs (4.6's) and transfer tomorrow, so I'll be makin an adaptor for the Soarer auto...
|
|
|
Post by Yarno on Aug 26, 2008 19:55:57 GMT 11
Just picked these up transfer coming...
|
|
|
Post by Yarno on Sept 3, 2008 7:11:26 GMT 11
|
|
|
Post by holden on Sept 3, 2008 15:21:49 GMT 11
ITS GOING TO BE REALLY WIDE !!!!!!!
ps: you have a flat tyre.
|
|
|
Post by Yarno on Sept 17, 2008 18:15:27 GMT 11
Got the MU sitting on the bump stops here and pumped the tyre up. Going to need some guard trimming at the front but only under the light and blinker by the looks of it. Showing the extra width...
|
|
|
Post by Yarno on Sept 17, 2008 18:22:46 GMT 11
Decided to see if the engine was even going to fit, so I looked at it and thought taking the gearbox off was too hard and spent a few hours fitting a square box into a triangle hole... mmm fun. fits in just You can see here on full straight down compression where I need to cut... later...
|
|
|
Post by Yarno on Sept 17, 2008 18:29:08 GMT 11
I am going to have to take the Soarer headers off and modify them as they don't fit between the rails and is in the way of the drive shaft under compression. Also found that the steering shafts are the same, and if I had a standard MU one it would have fitted straight on, so I'll have to remove the extension that I made with the 3" body lift.
|
|
|
Post by Yarno on Dec 6, 2008 13:42:34 GMT 11
|
|
|
Post by holden on Dec 6, 2008 14:00:04 GMT 11
Nice jig. ;D
|
|
|
Post by Bruce on Dec 6, 2008 20:29:16 GMT 11
Nice job so far Yarno, looking forward to the end product.
Cheers Bruce.
|
|